Gerbing battery hook up cable

When you install the battery harness you must connect the positive bolt and cable first. Negative Terminal Remove the bolt that holds the negative battery terminal in place. The negative terminal is marked on the battery post with a -. Identify the negative wire of your battery harness. The negative wire does not have the fuse in-line. Positive Terminal Remove the bolt that holds the positive battery cable in place.

Identify the positive wire of your battery harness. The positive wire has the fuse in-line. Replace the positive bolt and cable first. At the end of your battery harness is an o-ring connector. Place the bolt through the o-ring connector and tighten. Reconnect the negative bolt and cable. Route the battery harness to the left side of the vehicle.

Make sure the wires will not rub or be pinched between the frame and the seat. Let the battery harness plug hang a couple of inches out from under the seat on the left side. Zip-tie or use electrical tape to safely attach the wire to the frame or other points on the vehicle to prevent the wire from moving. Double check that your battery terminal bolts and cabling are correct and tight.

If you do have an accessory port on your motorcycle, check with your manufacturer to ensure that you have the correct fuse rating to safely operate your heating clothing without damage to your charging system.

This warranty does not cover any damage caused by 1 normal wear and tear; 2 improper use; 3 failure to follow the product instructions; 4 modifications; 5 unauthorized repair; 6 external causes such as accidents, abuse, or other actions or events beyond our reasonable control; or 7 customer negligence.

Shipping costs for all warranty claims are the responsibility of the customer. What is the period of coverage? The heating elements in our products Microwire are covered for life. This warranty covers electrical plugs, connectors, solder joints, Gerbing temperature controllers, Gerbing electrical components of accessories, and all materials, sewing, and craftsmanship for one year from the date of purchase. Special care should be taken to prolong the life of your battery.

Batteries must only be used with products with an amp rating less than the maximum capacity output rating for the battery.

What are your remedies under this warranty? With respect to any defective product during the Warranty Period, we will, in our sole discretion, repair or replace such product or the defective part free of charge. In the event that the product or style warrantied is no longer available, a replacement style or credit may be offered for the original product value.

The Y-cable cannot be used for 7 volt heated gloves or 7 volt heated socks. Both the heated gloves and the heated socks have a different Y-cable. The 12 volt Gerbing Heated Gloves are supplied with a junior controller long Y-cable with a built-in temperature controller and a battery cable. With this set you are able to connect your heated gloves to the battery of a vehicle. If you want to undertake outdoor activities you can connect the 12 volt heated gloves to a portable battery like the B12v or the B12v You will need a Y-cable because it is not possible to connect the Gerbing portable batteries to a junior controller.

The 12 volt Gerbing heated socks come standard with a long Y-cable and battery cable. With this set you are able to connect your heated socks to the battery of a vehicle.

You can also use this Y-cable to the portable 12 volt batteries. If you want to regulate the temperature you will need the single portable controller. It is not possible to use a junior controller with our 12 volt socks. Splitter Y scurt Splitter to connect heated gloves and heated socks The Gerbing splitter is an accessory that at first was developed for our Gerbing 12 volt electric heated socks to connect to the heated gloves. The splitter makes is possible to connect two products to one battery hook-up.

This way it is for example possible to connect heated socks and heated gloves to the splitter so there is only one connection to the battery hook-up. Only the Gerbing 12 volt products can be connected to the splitter. When you use the Gerbing splitter we recommend to use a temperature controller for the heated gloves and heated socks. For the heated socks you can use a single portable temperature controller optional and for the heated gloves a junior controller which comes with the product.

Our heated gloves and heated socks will get a warmer feel as the temperature outside increases. A temperature controller makes it possible for you to regulate the heat. With the splitter you make your heated gloves and heated socks one heating system.

That means that the garments wil be the same temperature. When you want to heat the products separately than you use the dual temperature controller.

25 Best Gerbing - Heated Gloves, Jackets, etc. images in | Gloves, Mittens, Free delivery

If your size is no longer available from us, please contact us so that we can inquire whether if they can still be ordered. This heated textile gloves are light and easy to wear. Intended for use on the moped , scooter or quad. Not suitable for motorcyclists.

Gerbing XR12 Heated Gloves

We are a motorcycle parts and accessories mail order specialist based in Ashford, Middlesex and we have been supplying all the best brands in biking on-line since We sell only tried and tested products that offer great value and top quality and would happily use ourselves. Low prices and a top quality service is our promise to you. We hold huge stocks which is increasing all the time and will always do our best to deliver your parts in the UK within working days. Please browse our products either by category or by using the search box at the top of the screen.